When utilizing a full-depth cutout as the cut style, you can select the edit button next to “Use Tabs” to adjust the positioning of their tabs. If you unselect this option, make sure the piece is still clamped down and won’t move when cut out. When doing a Full Depth Cutout, Easel can add tabs automatically to keep the piece in place. Padding:Įxtra space carved around the model, when “Rectangle Relief” or "Model Boundary Relief" has been selected as a cut style. Total depth carved as measured from the top surface of the material (Z-axis). The material’s height should be at least equal to the model’s size for it to be carved properly. For detailed information, see this guide: Origin Safety Height vs Safety Height Material height: Safety height:ĭistance from the bit to the surface of the material during rapid movements. For models with vertical spaces to be carved, the bit length will be the maximum possible cut depth. The length of the tool as measured from the bottom side of the collet to the tip of the bit. Model Boundary Relief will only carve within the boundaries of the model, leaving stock around its edges. Rectangle Relief will carve a rectangular space around the model on the X and Y plane.ģ. Full Depth Cutout with Autotabs will completely cut the model out of the stock, keeping it in place with tabs.Ģ. There are three options for carving your model:ġ. Use this function to spin the model counterclockwise by a specific angle on the XY plane. You can change any value by itself or change them proportionately, using “Lock XY” to keep only width and length proportionate, or “Lock XYZ” to keep width, length and height proportionate. The width, length and height of the model. This can also be set as a negative value to carve only part of a model on the stock. The relative distance of the model from work zero (the purple 0,0,0 point on the grid). Not all models import into Easel facing up. It can be Top, Bottom, Left, Right, Front or Back. After you have generated the toolpaths, you may see how the finished piece will look after clicking the "Show Preview" button.Generate toolpaths to see the carving path and the approximate time it will take (the image below is sped up for instructions.) Easel will display the Carve Time Estimator with approximate carving times.For more information on calculating your cut settings, see this guide: Calculating Your Cut Settings: Basic Feeds and Speeds Information We recommend using Easel's default settings as a starting point. NOTE: If you are using a different type of material, your settings will be different or unlisted. Recommended Cut Settings for current X-Carve 1000mm (shown below) on Birch Plywood with 1/4" Downcut and 1/8" Ballnose: Recommended Cut Settings for X-Carve Pro (shown below) Birch Plywood with 1/4" Downcut and 1/8" Ballnose: Easel can recommend general, safe cut settings for both passes, but you might need a bit of experimentation to find what works best for your combination of bit and material.In general, any end mill bit ¼” or ⅛” diameter will work well as a roughing bit for the finishing pass, we strongly recommend using a ⅛” ballnose bit. Select the bits you will use for the roughing pass and finishing pass.You can also select the direction of the finishing toolpath (e.g. Select the Cut Style you want for your model (see below for the Cut Style options).You can use "Center to material" to quickly position the object to the middle of the material. The purple box represents the overall dimensions of your model. The green box represents the size of the material. Orient and position your model where you want it to be carved on the material, making sure that the model is within its boundaries.Make sure the stock size will be enough to completely carve the model (especially the height). Once your model is loaded, enter the size of the stock material you will use for carving your 3D model.Open up a new Easel Project and select "Import 3D STL File" to load your model.If you have a 3D file in another format, you will need to convert it to. You could also try the Intro to Easel Project.ģD in Easel Pro will only work with STL files. First time ever using Easel? We recommend having a quick look at how Easel works before attempting your first 3D carve: Designing in Easel.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |